Eaton HC2-R68-R 0.63 uH Ferrite Foil Inductor
Eaton HC2-R68-R 0.63 uH Ferrite Foil Inductor

Eaton HC2-R68-R 0.63 uH Ferrite Foil Inductor

Share
Eaton HC2-R68-R: foil-wound high-current inductor, 0.63 uH ±20%, 52.9 A Irms, Isat 50 A, DCR 0.6 mOhm, 19.2 x 19.0 mm.
    • Product Details
    • Download

    Eaton HC2-R68-R .63 uH Ferrite Foil Inductor

    HC2-R68-R at a glance: foil-wound high-current inductor, .63 uH ±20%, 52.9 A Irms, Isat 50 A (20% rolloff @ +25 °C), DCR 0.6 mOhm, 19.2 x 19.0 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC2-R68-R
    Ordering code, tape and reelHC2-R68TR-R
    OCL (open circuit inductance).63 uH ±20%
    Irms (DC, 40 °C rise)52.9 A
    Isat (20% rolloff @ +25 °C)50 A
    DCR typical @ +20 °C0.6 mOhm
    Volt-time rating (V-us)6.87
    Package19.2 x 19.0 mm
    Height12.7 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4109

    Dimensions and Pad Layout

    HC2-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4109: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    The winding in this part is copper foil rather than magnet wire. Foil gives the conductor a wide, flat section, so the high-frequency current crowds into a much larger effective area and the AC resistance stays close to the DC value. On a low-voltage, high-current rail that is the difference between an inductor that runs cool at 300 kHz and one that cooks.

    At the rated 52.9 A the winding dissipates about 1.68 W in copper alone, using the typical DCR of 0.6 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 788 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    Where This Series Fits

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    The HC2 family spans 0.52 uH to 6 uH; this row sits at position 2 of 6.

    One step down the table, HC2-R47-R, sits at .52 uH with 52.9 A and 0.6 mOhm – the lower inductance buys about 19.9 A of extra current in the same body.

    • Core material: metal composite, 19.2 x 19.0 mm body at 12.7 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 0.6 mOhm becomes roughly 0.848 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Check the millivolt drop at rated current against the converter tolerance window.
    • Apply the AC derating curve before assuming the 40 °C rise figure holds.
    • Keep the peak current inside the saturation boundary with margin for inductance tolerance.

    Frequently Asked Questions

    What does the volt-microsecond column describe?
    It is the applied volt-time product that produces a core loss equal to 10 % of the total loss at a 40 °C rise. It is a way to compare core capability between parts at a given frequency.

    What does the volt-microsecond column describe?
    It is the applied volt-time product that produces a core loss equal to 10 % of the total loss at a 40 °C rise. It is a way to compare core capability between parts at a given frequency.

    Is the part suitable for a SEPIC or buck-boost stage?
    The inductance and current ratings suit it, but check the AC flux swing: in a buck-boost the inductor carries the full input current continuously, so the core loss is higher than in a buck stage of the same output.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products