Eaton HC2LP-R68-R 0.63 uH High-Current Inductor 0.6 mOhm
Eaton HC2LP-R68-R 0.63 uH High-Current Inductor 0.6 mOhm

Eaton HC2LP-R68-R 0.63 uH High-Current Inductor 0.6 mOhm

Share
Eaton HC2LP-R68-R: foil-wound high-current inductor, 0.63 uH ±20%, 52.9 A Irms, Isat 50 A, DCR 0.6 mOhm, 19.2 x 19.2 mm.
    • Product Details
    • Download

    Eaton HC2LP-R68-R .63 uH High-Current Inductor 0.6 mOhm

    HC2LP-R68-R at a glance: foil-wound high-current inductor, .63 uH ±20%, 52.9 A Irms, Isat 50 A (20% rolloff @ +25 °C), DCR 0.6 mOhm, 19.2 x 19.2 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHC2LP-R68-R
    OCL (open circuit inductance).63 uH ±20%
    Irms (DC, 40 °C rise)52.9 A
    Isat (20% rolloff @ +25 °C)50 A
    DCR typical @ +20 °C0.6 mOhm
    Volt-time rating (V-us)6.87
    Package19.2 x 19.2 mm
    Height11.18 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4114

    Mechanical Dimensions & Pad Layout

    HC2LP-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4114: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    A foil winding on a ferrite core is the classic answer to a hard combination: several tens of amps, a supply below 5 V, and a switching frequency high enough that skin depth has already eaten into round wire. The flat conductor keeps the window utilisation high, so DCR stays in the fractions of a milliohm.

    At the rated 52.9 A the winding dissipates about 1.68 W in copper alone, using the typical DCR of 0.6 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 788 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    What This Family Is For

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Of the 6 values listed for HC2LP, this is the 2th, in a family covering 0.52 uH to 6 uH.

    The next value up in the same family, HC2LP-1R0-R, gives 1.15 uH at 33 A and DCR 1.3 mOhm: the extra inductance costs about 19.9 A of rated current.

    • Core material: ferrite core, 19.2 x 19.2 mm body at 11.18 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 0.6 mOhm becomes roughly 0.848 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.

    Frequently Asked Questions

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    What does the DCR tolerance mean for paralleling?
    Parts are not matched for DCR, so two in parallel will not share current exactly. The mismatch is set by the DCR tolerance, and because the DCR is only fractions of a milliohm, a small absolute difference is a large percentage one.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products