Eaton HC3-6R0-R 6.52 uH Ferrite Foil Inductor
Eaton HC3-6R0-R 6.52 uH Ferrite Foil Inductor

Eaton HC3-6R0-R 6.52 uH Ferrite Foil Inductor

Share
Eaton HC3-6R0-R: foil-wound high-current inductor, 6.52 uH ±20%, 33.8 A Irms, Isat 30 A, DCR 2.17 mOhm, 30.0 x 25.3 mm.
    • Product Details
    • Download

    Eaton HC3-6R0-R 6.52 uH Ferrite Foil Inductor

    HC3-6R0-R at a glance: foil-wound high-current inductor, 6.52 uH ±20%, 33.8 A Irms, Isat 30 A (20% rolloff @ +25 °C), DCR 2.17 mOhm, 30.0 x 25.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC3-6R0-R
    OCL (open circuit inductance)6.52 uH ±20%
    Irms (DC, 40 °C rise)33.8 A
    Isat (20% rolloff @ +25 °C)30 A
    DCR typical @ +20 °C2.17 mOhm
    Volt-time rating (V-us)43.3
    Package30.0 x 25.3 mm
    Height18.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4122

    Outline Drawing

    HC3-6R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4122: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    A foil winding on a ferrite core is the classic answer to a hard combination: several tens of amps, a supply below 5 V, and a switching frequency high enough that skin depth has already eaten into round wire. The flat conductor keeps the window utilisation high, so DCR stays in the fractions of a milliohm.

    At the rated 33.8 A the winding dissipates about 2.48 W in copper alone, using the typical DCR of 2.17 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 2,934 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    What This Family Is For

    The HC foil family covers the low-inductance, very-high-current end of the range: sub-microhenry to a few microhenry, with DC resistance measured in fractions of a milliohm. It is the family to reach for when the rail is a volt or two and the current is tens of amps.

    Within the HC3 family this is value 7 of 7, in a range that runs from 0.5 uH to 6.52 uH.

    The next value up in the same family, HC3-5R6-R, gives 5.68 uH at 33.8 A and DCR 2.17 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: ferrite core, 30.0 x 25.3 mm body at 18.0 mm.
    • Typical applications: distributed power systems dc-dc converters; general-purpose low voltage supplies; computer systems; servers; point of load (pol) converters; industrial equipment.
    • The rated current assumes a 40 °C rise from DC alone. AC ripple raises the winding temperature further, and the derating curves in the data sheet are there for exactly that case.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.17 mOhm becomes roughly 3.07 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: on a low-voltage rail the DCR drop is a real fraction of the output. Compare the millivolt drop at rated current against the converter tolerance before choosing the smallest inductance in the family.

    • Leave clearance for the tape-and-reel orientation if the line places by vision.
    • At frequencies above a few hundred kilohertz, check the AC resistance rise before assuming the DC figure holds.
    • Check the millivolt drop at rated current against the converter tolerance window.

    Frequently Asked Questions

    What does the volt-microsecond column describe?
    It is the applied volt-time product that produces a core loss equal to 10 % of the total loss at a 40 °C rise. It is a way to compare core capability between parts at a given frequency.

    Why foil instead of round wire?
    At high frequency the current crowds into the surface of the conductor. A flat foil presents a wide surface for the same cross-section, so the AC resistance stays closer to the DC value and the winding runs cooler.

    Can this replace a powdered-core part of the same value?
    Only if the saturation behaviour is acceptable. Ferrite saturates abruptly compared with a powder core, so the transient margin has to be re-checked even when the inductance and DCR look similar.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products