Eaton HC8-R15-R 0.175 uH SMD Power Inductor, 1.5 V-us
Eaton HC8-R15-R 0.175 uH SMD Power Inductor, 1.5 V-us

Eaton HC8-R15-R 0.175 uH SMD Power Inductor, 1.5 V-us

Share
Eaton HC8-R15-R: powder iron high-current inductor, 0.175 uH ±20%, 39 A Irms, Isat 43 A, DCR 0.8 mOhm, 10.9 x 10.4 mm.
    • Product Details
    • Download

    Eaton HC8-R15-R 0.175 uH SMD Power Inductor, 1.5 V-us

    HC8-R15-R at a glance: powder iron high-current inductor, 0.175 uH ±20%, 39 A Irms, Isat 43 A (15% rolloff), DCR 0.8 mOhm, 10.9 x 10.4 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC8-R15-R
    OCL (open circuit inductance)0.175 uH ±20%
    Irms (DC, 40 °C rise)39 A
    Isat (15% rolloff)43 A
    Isat2 (30% rolloff)76 A
    DCR typical @ +20 °C0.8 mOhm
    Volt-time rating (V-us)1.5
    Package10.9 x 10.4 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4120

    Outline Drawing

    HC8-R15-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4120: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Powder iron is the material choice that gives this family its soft saturation curve and its stable inductance over temperature. There is no thermal aging of the binder, so the inductance you measure on day one is the inductance you have after a thousand thermal cycles.

    With 0.8 mOhm typical, the I-squared-R loss at the full 39 A rating is about 1.22 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 15% rolloff. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 162 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The second saturation column, 76 A at 30% rolloff, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Series Positioning

    The HC powder family sits at the higher-inductance end of the high-current range: from a fraction of a microhenry up to tens of microhenry, on surface-mount bodies with powder iron cores. Every row carries two saturation columns so the rolloff criterion can be chosen explicitly.

    Of the 16 values listed for HC8, this is the 1th, in a family covering 0.175 uH to 47.3 uH.

    Compared with its neighbours in the table, HC8-R39-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: powder iron core, 10.9 x 10.4 mm body at 4.0 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; desktop and server vrms and evrds; point-of-load (pol) modules; field programmable gate array (fpga) dc-dc converters.
    • The two saturation columns are different criteria, not two measurements of the same thing. Pick the rolloff you can tolerate in the application and stay with that column.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.8 mOhm becomes roughly 1.22 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: use the 30% rolloff column only if the loop can tolerate the inductance droop; the tighter column keeps more inductance at the cost of a lower usable peak current.

    • Check the volt-time rating against the applied V-us at the switching frequency.
    • Check the volt-time rating against the applied V-us at the switching frequency.
    • Confirm the part marking is visible after placement for traceability.

    Frequently Asked Questions

    What is soft saturation?
    The inductance falls gradually as current rises instead of collapsing at a threshold. A powder core with a distributed gap behaves this way, which keeps the converter stable through a load transient.

    Why is the DCR higher than a ferrite part of the same size?
    Iron powder has lower permeability, so more turns are needed for the same inductance, and more turns mean more copper. The compensation is the much higher saturation flux density.

    Why is the DCR higher than a ferrite part of the same size?
    Iron powder has lower permeability, so more turns are needed for the same inductance, and more turns mean more copper. The compensation is the much higher saturation flux density.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products