Eaton HC8LP-150-R 15.2 uH SMD Power Inductor, 11.6 V-us
Eaton HC8LP-150-R 15.2 uH SMD Power Inductor, 11.6 V-us

Eaton HC8LP-150-R 15.2 uH SMD Power Inductor, 11.6 V-us

Share
Eaton HC8LP-150-R: powder iron high-current inductor, 15.2 uH ±20%, 3.4 A Irms, Isat 3.1 A, DCR 99.4 mOhm, 10.9 x 10.4 mm.
    • Product Details
    • Download

    Eaton HC8LP-150-R 15.2 uH SMD Power Inductor, 11.6 V-us

    HC8LP-150-R at a glance: powder iron high-current inductor, 15.2 uH ±20%, 3.4 A Irms, Isat 3.1 A (15% rolloff), DCR 99.4 mOhm, 10.9 x 10.4 mm.

    Specification Table

    ParameterValue
    Orderable part numberHC8LP-150-R
    OCL (open circuit inductance)15.2 uH ±20%
    Irms (DC, 40 °C rise)3.4 A
    Isat (15% rolloff)3.1 A
    Isat2 (30% rolloff)5.5 A
    DCR typical @ +20 °C99.4 mOhm
    Volt-time rating (V-us)11.6
    Package10.9 x 10.4 mm
    Height3.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4126

    Dimensions and Pad Layout

    HC8LP-150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4126: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    This is a surface-mount inductor on a distributed air gap: the powder core spreads the gap through the whole volume, which is why the part tolerates large DC bias without a cliff in the inductance curve, and why it is used on multiphase rails where the inductors share current.

    The DCR figure of 99.4 mOhm is what sets the efficiency: at 3.4 A the winding drops about 0.338 mV and dissipates 1.15 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 15% rolloff, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 73 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The second saturation column, 5.5 A at 30% rolloff, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Series Positioning

    The HC powder family sits at the higher-inductance end of the high-current range: from a fraction of a microhenry up to tens of microhenry, on surface-mount bodies with powder iron cores. Every row carries two saturation columns so the rolloff criterion can be chosen explicitly.

    The HC8LP family spans 0.17 uH to 47.9 uH; this row sits at position 13 of 16.

    One step down the table, HC8LP-100-R, sits at 9.90 uH with 4.3 A and 62.9 mOhm – the lower inductance buys about 1.5 A of extra current in the same body.

    • Core material: powder iron core, 10.9 x 10.4 mm body at 3.5 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; notebook and laptop regulators; desktop and server vrms and evrds; point-of-load (pol) modules.
    • The two saturation columns are different criteria, not two measurements of the same thing. Pick the rolloff you can tolerate in the application and stay with that column.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 99.4 mOhm becomes roughly 152 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: use the 30% rolloff column only if the loop can tolerate the inductance droop; the tighter column keeps more inductance at the cost of a lower usable peak current.

    • Decide which rolloff column the loop can tolerate, then stay with that column.
    • Confirm the part marking is visible after placement for traceability.
    • Confirm the part marking is visible after placement for traceability.

    Frequently Asked Questions

    Why is the DCR higher than a ferrite part of the same size?
    Iron powder has lower permeability, so more turns are needed for the same inductance, and more turns mean more copper. The compensation is the much higher saturation flux density.

    Is the part shielded?
    The winding is enclosed by the powder core, so the external field is small. It is not a closed ferrite shield, but the fringing field is low enough for dense board layouts.

    Which saturation column should I design to?
    The one that matches the inductance droop your loop can tolerate. The 30 % column gives a higher usable peak current; the tighter column keeps more inductance at the cost of headroom.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message