Eaton HC8LP-2R6-R Powder Iron Inductor 2.67 uH, Isat 7.4 A
Eaton HC8LP-2R6-R Powder Iron Inductor 2.67 uH, Isat 7.4 A

Eaton HC8LP-2R6-R Powder Iron Inductor 2.67 uH, Isat 7.4 A

Share
Eaton HC8LP-2R6-R: powder iron high-current inductor, 2.67 uH ±20%, 8.3 A Irms, Isat 7.4 A, DCR 17.1 mOhm, 10.9 x 10.4 mm.
    • Product Details
    • Download

    Eaton HC8LP-2R6-R Powder Iron Inductor 2.67 uH, Isat 7.4 A

    HC8LP-2R6-R at a glance: powder iron high-current inductor, 2.67 uH ±20%, 8.3 A Irms, Isat 7.4 A (15% rolloff), DCR 17.1 mOhm, 10.9 x 10.4 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC8LP-2R6-R
    OCL (open circuit inductance)2.67 uH ±20%
    Irms (DC, 40 °C rise)8.3 A
    Isat (15% rolloff)7.4 A
    Isat2 (30% rolloff)13.1 A
    DCR typical @ +20 °C17.1 mOhm
    Volt-time rating (V-us)4.8
    Package10.9 x 10.4 mm
    Height3.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4126

    Dimensions and Pad Layout

    HC8LP-2R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4126: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Powder iron is the material choice that gives this family its soft saturation curve and its stable inductance over temperature. There is no thermal aging of the binder, so the inductance you measure on day one is the inductance you have after a thousand thermal cycles.

    Copper loss at the rated current works out to roughly 1.18 W from a typical DCR of 17.1 mOhm at 8.3 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 15% rolloff, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 73.1 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The second saturation column, 13.1 A at 30% rolloff, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Where This Series Fits

    The HC powder family sits at the higher-inductance end of the high-current range: from a fraction of a microhenry up to tens of microhenry, on surface-mount bodies with powder iron cores. Every row carries two saturation columns so the rolloff criterion can be chosen explicitly.

    The HC8LP family spans 0.17 uH to 47.9 uH; this row sits at position 6 of 16.

    Compared with its neighbours in the table, HC8LP-3R5-R trades 3.2 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: powder iron core, 10.9 x 10.4 mm body at 3.5 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; notebook and laptop regulators; desktop and server vrms and evrds; point-of-load (pol) modules.
    • The two saturation columns are different criteria, not two measurements of the same thing. Pick the rolloff you can tolerate in the application and stay with that column.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 17.1 mOhm becomes roughly 26.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: use the 30% rolloff column only if the loop can tolerate the inductance droop; the tighter column keeps more inductance at the cost of a lower usable peak current.

    • Check the volt-time rating against the applied V-us at the switching frequency.
    • Decide which rolloff column the loop can tolerate, then stay with that column.
    • Confirm the part marking is visible after placement for traceability.

    Frequently Asked Questions

    What is soft saturation?
    The inductance falls gradually as current rises instead of collapsing at a threshold. A powder core with a distributed gap behaves this way, which keeps the converter stable through a load transient.

    Does the inductance drift with age?
    The binder is non-organic and the core is not gapped with adhesive, so thermal aging of the magnetic path is not a mechanism here. The value is stable across thermal cycles.

    Which saturation column should I design to?
    The one that matches the inductance droop your loop can tolerate. The 30 % column gives a higher usable peak current; the tighter column keeps more inductance at the cost of headroom.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products