Eaton HC8LP-R39-R Powder Iron Inductor 0.430 uH, Isat 19 A
Eaton HC8LP-R39-R Powder Iron Inductor 0.430 uH, Isat 19 A

Eaton HC8LP-R39-R Powder Iron Inductor 0.430 uH, Isat 19 A

Share
Eaton HC8LP-R39-R: powder iron high-current inductor, 0.430 uH ±20%, 20.2 A Irms, Isat 19 A, DCR 2.8 mOhm, 10.9 x 10.4 mm.
    • Product Details
    • Download

    Eaton HC8LP-R39-R Powder Iron Inductor 0.430 uH, Isat 19 A

    HC8LP-R39-R at a glance: powder iron high-current inductor, 0.430 uH ±20%, 20.2 A Irms, Isat 19 A (15% rolloff), DCR 2.8 mOhm, 10.9 x 10.4 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHC8LP-R39-R
    OCL (open circuit inductance)0.430 uH ±20%
    Irms (DC, 40 °C rise)20.2 A
    Isat (15% rolloff)19 A
    Isat2 (30% rolloff)34 A
    DCR typical @ +20 °C2.8 mOhm
    Volt-time rating (V-us)4.7
    Package10.9 x 10.4 mm
    Height3.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4126

    Mechanical Dimensions & Pad Layout

    HC8LP-R39-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4126: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    A powder core with a non-organic binder is a deliberately conservative choice: it trades a little permeability for predictable behaviour at high current and high temperature. The result is an inductor that stays linear enough for a current-mode loop to be designed around it.

    With 2.8 mOhm typical, the I-squared-R loss at the full 20.2 A rating is about 1.14 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Isat is specified as 15% rolloff, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 77.6 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The second saturation column, 34 A at 30% rolloff, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Series Positioning

    The HC powder family sits at the higher-inductance end of the high-current range: from a fraction of a microhenry up to tens of microhenry, on surface-mount bodies with powder iron cores. Every row carries two saturation columns so the rolloff criterion can be chosen explicitly.

    Within the HC8LP family this is value 2 of 16, in a range that runs from 0.17 uH to 47.9 uH.

    One step down the table, HC8LP-R15-R, sits at 0.170 uH with 29 A and 1.4 mOhm – the lower inductance buys about 13.4 A of extra current in the same body.

    • Core material: powder iron core, 10.9 x 10.4 mm body at 3.5 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; notebook and laptop regulators; desktop and server vrms and evrds; point-of-load (pol) modules.
    • The two saturation columns are different criteria, not two measurements of the same thing. Pick the rolloff you can tolerate in the application and stay with that column.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.8 mOhm becomes roughly 4.29 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: use the 30% rolloff column only if the loop can tolerate the inductance droop; the tighter column keeps more inductance at the cost of a lower usable peak current.

    • Compare the two saturation columns before fixing the current limit in the controller.
    • Confirm the part marking is visible after placement for traceability.
    • Confirm the part marking is visible after placement for traceability.

    Frequently Asked Questions

    Does the inductance drift with age?
    The binder is non-organic and the core is not gapped with adhesive, so thermal aging of the magnetic path is not a mechanism here. The value is stable across thermal cycles.

    Is the part shielded?
    The winding is enclosed by the powder core, so the external field is small. It is not a closed ferrite shield, but the fringing field is low enough for dense board layouts.

    Does the inductance drift with age?
    The binder is non-organic and the core is not gapped with adhesive, so thermal aging of the magnetic path is not a mechanism here. The value is stable across thermal cycles.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products