Eaton HCF1305-1R0-R 1.00 uH High-Current Inductor 1.58 mOhm
Eaton HCF1305-1R0-R 1.00 uH High-Current Inductor 1.58 mOhm

Eaton HCF1305-1R0-R 1.00 uH High-Current Inductor 1.58 mOhm

Share
Eaton HCF1305-1R0-R: ferrite high-current power inductor, 1.00 uH ±20%, 22 A Irms, Isat 24 A, DCR 1.58 mOhm, 12.5 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCF1305-1R0-R 1.00 uH High-Current Inductor 1.58 mOhm

    HCF1305-1R0-R at a glance: ferrite high-current power inductor, 1.00 uH ±20%, 22 A Irms, Isat 24 A (30% rolloff @ +25 °C), DCR 1.58 mOhm, 12.5 x 12.5 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCF1305-1R0-R
    Rated inductance1 uH ±20%
    OCL (open circuit inductance)1.00 uH ±20%
    Irms (DC, 40 °C rise)22 A
    Isat (30% rolloff @ +25 °C)24 A
    Isat2 (30% rolloff @ +125 °C)20 A
    DCR typical @ +20 °C1.58 mOhm
    DCR maximum @ +20 °C1.9 mOhm
    K-factor (Bp-p = K x L x dI)14, Bp-p in mT
    Package12.5 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4133

    Mechanical Drawing

    HCF1305-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4133: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Ferrite core, high current, and a winding built to keep the DC resistance low: this family sits between the foil-wound parts and the molded powder parts. Ferrite gives low core loss at the switching frequency; the construction gives a low DCR and a tight tolerance, which matters when the inductor is also the current-sense element.

    The DCR figure of 1.58 mOhm is what sets the efficiency: at 22 A the winding drops about 0.035 mV and dissipates 0.765 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 30% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 288 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 14 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 14 mT of Bp-p, the figure the core-loss curve is plotted against.

    The second saturation column, 20 A at 30% rolloff @ +125 °C, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Series Positioning

    The HCF family is the ferrite option in the high-current range: lower core loss than a powder part at high frequency, with saturation current quoted at both +25 °C and +125 °C. It is the family for converters that run fast and hot.

    Of the 10 values listed for HCF1305, this is the 3th, in a family covering 0.47 uH to 4.7 uH.

    The next value up in the same family, HCF1305-1R2-R, gives 1.20 uH at 22 A and DCR 1.58 mOhm: the extra inductance costs about 10 A of rated current.

    • Core material: ferrite core, 12.5 x 12.5 mm body at 5.0 mm.
    • Typical applications: voltage regulator modules (vrm); high current dc-dc converters; multi-phase buck regulators; servers and data networking; point-of-load modules.
    • Ferrite loses saturation margin as it heats. The +125 °C Isat column is the one that governs a hot design; the +25 °C figure is the optimistic one.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.9 mOhm becomes roughly 2.68 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the full-load inductance (FLL) is the value to use for ripple at rated current. OCL is the small-signal number; FLL is what the converter actually sees under load.

    • Confirm the terminal arrangement matches the pad layout for three-terminal parts.
    • Calculate ripple with FLL, not OCL: the loaded inductance is what the converter sees.
    • Check saturation at the +125 °C column when the enclosure runs hot.

    Frequently Asked Questions

    Is this part suitable for current sensing?
    The family includes parts with tight DCR tolerance for exactly that purpose, but the tolerance is quoted at +20 °C. Copper drift with temperature has to be compensated in the sensing circuit.

    Is a three-terminal part a drop-in for a two-terminal one?
    No. The third terminal is part of the construction and changes the pad layout and the current path, so the board needs the matching footprint.

    Why are there two saturation currents?
    Ferrite loses saturation flux density as it heats. The +25 °C column describes a bench measurement; the +125 °C column describes the part under load in a hot enclosure, which is the one that governs the design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products