Eaton HCF1305-4R7-R Ferrite Inductor 4.70 uH, Isat 10.4 A
Eaton HCF1305-4R7-R Ferrite Inductor 4.70 uH, Isat 10.4 A

Eaton HCF1305-4R7-R Ferrite Inductor 4.70 uH, Isat 10.4 A

Share
Eaton HCF1305-4R7-R: ferrite high-current power inductor, 4.70 uH ±20%, 10.9 A Irms, Isat 10.4 A, DCR 6 mOhm, 12.5 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCF1305-4R7-R Ferrite Inductor 4.70 uH, Isat 10.4 A

    HCF1305-4R7-R at a glance: ferrite high-current power inductor, 4.70 uH ±20%, 10.9 A Irms, Isat 10.4 A (30% rolloff @ +25 °C), DCR 6 mOhm, 12.5 x 12.5 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCF1305-4R7-R
    Rated inductance4.7 uH ±20%
    OCL (open circuit inductance)4.70 uH ±20%
    Irms (DC, 40 °C rise)10.9 A
    Isat (30% rolloff @ +25 °C)10.4 A
    Isat2 (30% rolloff @ +125 °C)7.5 A
    DCR typical @ +20 °C6 mOhm
    DCR maximum @ +20 °C7.2 mOhm
    K-factor (Bp-p = K x L x dI)6.9, Bp-p in mT
    Package12.5 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4133

    Dimensions and Pad Layout

    HCF1305-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4133: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Ferrite core, high current, and a winding built to keep the DC resistance low: this family sits between the foil-wound parts and the molded powder parts. Ferrite gives low core loss at the switching frequency; the construction gives a low DCR and a tight tolerance, which matters when the inductor is also the current-sense element.

    With 6 mOhm typical, the I-squared-R loss at the full 10.9 A rating is about 0.713 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 30% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 254 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 6.9 means the flux swing is about 32.4 mT per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    The second saturation column, 7.5 A at 30% rolloff @ +125 °C, is the same core taken further into rolloff. The ratio between the two columns is a direct measure of how soft the curve is: a part with a wide gap between them loses inductance slowly and tolerates a larger transient peak.

    Series Positioning

    The HCF family is the ferrite option in the high-current range: lower core loss than a powder part at high frequency, with saturation current quoted at both +25 °C and +125 °C. It is the family for converters that run fast and hot.

    Of the 10 values listed for HCF1305, this is the 10th, in a family covering 0.47 uH to 4.7 uH.

    Compared with its neighbours in the table, HCF1305-4R0-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: ferrite core, 12.5 x 12.5 mm body at 5.0 mm.
    • Typical applications: voltage regulator modules (vrm); high current dc-dc converters; multi-phase buck regulators; servers and data networking; point-of-load modules.
    • Ferrite loses saturation margin as it heats. The +125 °C Isat column is the one that governs a hot design; the +25 °C figure is the optimistic one.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 7.2 mOhm becomes roughly 10.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the full-load inductance (FLL) is the value to use for ripple at rated current. OCL is the small-signal number; FLL is what the converter actually sees under load.

    • Calculate ripple with FLL, not OCL: the loaded inductance is what the converter sees.
    • Calculate ripple with FLL, not OCL: the loaded inductance is what the converter sees.
    • Calculate ripple with FLL, not OCL: the loaded inductance is what the converter sees.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive and no longer behaves as an inductor. Keep the switching frequency and the harmonics that carry energy comfortably below SRF where one is quoted.

    Is a three-terminal part a drop-in for a two-terminal one?
    No. The third terminal is part of the construction and changes the pad layout and the current path, so the board needs the matching footprint.

    Is a three-terminal part a drop-in for a two-terminal one?
    No. The third terminal is part of the construction and changes the pad layout and the current path, so the board needs the matching footprint.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message