Eaton HCM0503-220-R 22 uH Molded Power Inductor, 1.9 A
Eaton HCM0503-220-R 22 uH Molded Power Inductor, 1.9 A

Eaton HCM0503-220-R 22 uH Molded Power Inductor, 1.9 A

Share
Eaton HCM0503-220-R: molded high-current power inductor, 22 uH ±20%, 1.9 A Irms, Isat 1.9 A, DCR 260 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM0503-220-R 22 uH Molded Power Inductor, 1.9 A

    HCM0503-220-R at a glance: molded high-current power inductor, 22 uH ±20%, 1.9 A Irms, Isat 1.9 A (20% rolloff @ +25 °C), DCR 260 mOhm, 5.5 x 5.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM0503-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14 uH
    Irms (DC, 40 °C rise)1.9 A
    Isat (20% rolloff @ +25 °C)1.9 A
    DCR typical @ +20 °C260 mOhm
    DCR maximum @ +20 °C270 mOhm
    K-factor (Bp-p = K x L x dI)106, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4430

    Mechanical Dimensions & Pad Layout

    HCM0503-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4430: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    This is one of the molded power inductors used across VRM, point-of-load and multiphase regulator designs. The family covers a wide inductance range in standard footprints, and every row is characterised for both typical and maximum DCR so the loss budget can be built either way.

    At the rated 1.9 A the winding dissipates about 0.939 W in copper alone, using the typical DCR of 260 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 39.7 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 106 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,332 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 13 values listed for HCM0503, this is the 13th, in a family covering 0.2 uH to 22 uH.

    The next value up in the same family, HCM0503-150-R, gives 15 uH at 2.4 A and DCR 138 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 270 mOhm becomes roughly 381 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Build the thermal design on the maximum DCR, not the typical one.
    • Verify the body height against the enclosure or heat-spreader clearance.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.

    Frequently Asked Questions

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products