Eaton HCM0503-5R6-R 5.6 uH Shielded Power Inductor
Eaton HCM0503-5R6-R 5.6 uH Shielded Power Inductor

Eaton HCM0503-5R6-R 5.6 uH Shielded Power Inductor

Share
Eaton HCM0503-5R6-R: molded high-current power inductor, 5.6 uH ±20%, 4.3 A Irms, Isat 3.5 A, DCR 63 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM0503-5R6-R 5.6 uH Shielded Power Inductor

    HCM0503-5R6-R at a glance: molded high-current power inductor, 5.6 uH ±20%, 4.3 A Irms, Isat 3.5 A (20% rolloff @ +25 °C), DCR 63 mOhm, 5.5 x 5.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM0503-5R6-R
    OCL (open circuit inductance)5.6 uH ±20%
    FLL minimum, at Isat3.6 uH
    Irms (DC, 40 °C rise)4.3 A
    Isat (20% rolloff @ +25 °C)3.5 A
    DCR typical @ +20 °C63 mOhm
    DCR maximum @ +20 °C70.6 mOhm
    K-factor (Bp-p = K x L x dI)206, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4430

    Mechanical Drawing

    HCM0503-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4430: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    A molded body around an alloy or iron powder core: the winding is pressed into the magnetic material, so the field is contained inside the part and the terminals come straight out of the molding. The result is a shielded inductor with a low profile and a soft saturation curve, on a footprint that is almost all magnetic material.

    Copper loss at the rated current works out to roughly 1.17 W from a typical DCR of 63 mOhm at 4.3 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 34.3 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 206 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,154 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 13 values listed for HCM0503, this is the 10th, in a family covering 0.2 uH to 22 uH.

    The next value up in the same family, HCM0503-100-R, gives 10 uH at 2.8 A and DCR 122 mOhm: the extra inductance costs about 1.7 A of rated current.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 70.6 mOhm becomes roughly 99.7 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Confirm the shielding is adequate for the adjacent trace routing.
    • Check the hot DCR before signing off the efficiency budget.

    Frequently Asked Questions

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message