Eaton HCM0703-1R0-R Molded Inductor 1.0 uH, Isat 22 A
Eaton HCM0703-1R0-R Molded Inductor 1.0 uH, Isat 22 A

Eaton HCM0703-1R0-R Molded Inductor 1.0 uH, Isat 22 A

Share
Eaton HCM0703-1R0-R: molded high-current power inductor, 1.0 uH ±20%, 11 A Irms, Isat 22 A, DCR 9 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-1R0-R Molded Inductor 1.0 uH, Isat 22 A

    HCM0703-1R0-R at a glance: molded high-current power inductor, 1.0 uH ±20%, 11 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 9 mOhm, 7.4 x 6.8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM0703-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.6 uH
    Irms (DC, 40 °C rise)11 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C9 mOhm
    DCR maximum @ +20 °C10 mOhm
    K-factor (Bp-p = K x L x dI)374, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Dimensions and Pad Layout

    HCM0703-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    At the rated 11 A the winding dissipates about 1.09 W in copper alone, using the typical DCR of 9 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 242 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 374 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 374 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    The HCM0703 family spans 0.15 uH to 33 uH; this row sits at position 6 of 16.

    One step down the table, HCM0703-R82-R, sits at 0.82 uH with 13 A and 6.7 mOhm – the lower inductance buys about 4 A of extra current in the same body.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 10 mOhm becomes roughly 14.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the shielding is adequate for the adjacent trace routing.
    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.

    Frequently Asked Questions

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products