Eaton HCM0703-220-R Molded Inductor 22 uH, Isat 3 A
Eaton HCM0703-220-R Molded Inductor 22 uH, Isat 3 A

Eaton HCM0703-220-R Molded Inductor 22 uH, Isat 3 A

Share
Eaton HCM0703-220-R: molded high-current power inductor, 22 uH ±20%, 2.3 A Irms, Isat 3 A, DCR 135 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-220-R Molded Inductor 22 uH, Isat 3 A

    HCM0703-220-R at a glance: molded high-current power inductor, 22 uH ±20%, 2.3 A Irms, Isat 3 A (20% rolloff @ +25 °C), DCR 135 mOhm, 7.4 x 6.8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM0703-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14.1 uH
    Irms (DC, 40 °C rise)2.3 A
    Isat (20% rolloff @ +25 °C)3 A
    DCR typical @ +20 °C135 mOhm
    DCR maximum @ +20 °C149 mOhm
    K-factor (Bp-p = K x L x dI)83, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Outline Drawing

    HCM0703-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    At the rated 2.3 A the winding dissipates about 0.714 W in copper alone, using the typical DCR of 135 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 99 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 83, a peak-to-peak ripple of one amp produces roughly 1,826 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 16 values listed for HCM0703, this is the 15th, in a family covering 0.15 uH to 33 uH.

    The next value up in the same family, HCM0703-330-R, gives 33 uH at 1.8 A and DCR 220 mOhm: the extra inductance costs about 0.4 A of rated current.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 149 mOhm becomes roughly 210 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Build the thermal design on the maximum DCR, not the typical one.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.

    Frequently Asked Questions

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products