Eaton HCM0703-2R2-R 2.2 uH High-Current Inductor 18 mOhm
Eaton HCM0703-2R2-R 2.2 uH High-Current Inductor 18 mOhm

Eaton HCM0703-2R2-R 2.2 uH High-Current Inductor 18 mOhm

Share
Eaton HCM0703-2R2-R: molded high-current power inductor, 2.2 uH ±20%, 8 A Irms, Isat 14 A, DCR 18 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-2R2-R 2.2 uH High-Current Inductor 18 mOhm

    HCM0703-2R2-R at a glance: molded high-current power inductor, 2.2 uH ±20%, 8 A Irms, Isat 14 A (20% rolloff @ +25 °C), DCR 18 mOhm, 7.4 x 6.8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM0703-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.3 uH
    Irms (DC, 40 °C rise)8 A
    Isat (20% rolloff @ +25 °C)14 A
    DCR typical @ +20 °C18 mOhm
    DCR maximum @ +20 °C20 mOhm
    K-factor (Bp-p = K x L x dI)281, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Outline Drawing

    HCM0703-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    This is one of the molded power inductors used across VRM, point-of-load and multiphase regulator designs. The family covers a wide inductance range in standard footprints, and every row is characterised for both typical and maximum DCR so the loss budget can be built either way.

    At the rated 8 A the winding dissipates about 1.15 W in copper alone, using the typical DCR of 18 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    At Isat the part holds about 216 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 281 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 618 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 16 values listed for HCM0703, this is the 8th, in a family covering 0.15 uH to 33 uH.

    The next value up in the same family, HCM0703-3R3-R, gives 3.3 uH at 6 A and DCR 28 mOhm: the extra inductance costs about 3 A of rated current.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 20 mOhm becomes roughly 28.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the shielding is adequate for the adjacent trace routing.
    • Check the hot DCR before signing off the efficiency budget.
    • Verify the body height against the enclosure or heat-spreader clearance.

    Frequently Asked Questions

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products