Eaton HCM0703-3R3-R 3.3 uH Molded Power Inductor, 6 A
Eaton HCM0703-3R3-R 3.3 uH Molded Power Inductor, 6 A

Eaton HCM0703-3R3-R 3.3 uH Molded Power Inductor, 6 A

Share
Eaton HCM0703-3R3-R: molded high-current power inductor, 3.3 uH ±20%, 6 A Irms, Isat 13.5 A, DCR 28 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-3R3-R 3.3 uH Molded Power Inductor, 6 A

    HCM0703-3R3-R at a glance: molded high-current power inductor, 3.3 uH ±20%, 6 A Irms, Isat 13.5 A (20% rolloff @ +25 °C), DCR 28 mOhm, 7.4 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM0703-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2 uH
    Irms (DC, 40 °C rise)6 A
    Isat (20% rolloff @ +25 °C)13.5 A
    DCR typical @ +20 °C28 mOhm
    DCR maximum @ +20 °C30 mOhm
    K-factor (Bp-p = K x L x dI)252, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Mechanical Dimensions & Pad Layout

    HCM0703-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    The DCR figure of 28 mOhm is what sets the efficiency: at 6 A the winding drops about 0.168 mV and dissipates 1.01 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 301 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 252, a peak-to-peak ripple of one amp produces roughly 832 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Within the HCM0703 family this is value 9 of 16, in a range that runs from 0.15 uH to 33 uH.

    Compared with its neighbours in the table, HCM0703-4R7-R trades 2.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 30 mOhm becomes roughly 42.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Verify the body height against the enclosure or heat-spreader clearance.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.

    Frequently Asked Questions

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Why quote typical and maximum DCR?
    A guaranteed thermal design uses the maximum. A nominal efficiency calculation uses the typical. Publishing both lets the same table serve either purpose.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products