Eaton HCM0703-4R7-R 4.7 uH Shielded Power Inductor
Eaton HCM0703-4R7-R 4.7 uH Shielded Power Inductor

Eaton HCM0703-4R7-R 4.7 uH Shielded Power Inductor

Share
Eaton HCM0703-4R7-R: molded high-current power inductor, 4.7 uH ±20%, 5.5 A Irms, Isat 10 A, DCR 37 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-4R7-R 4.7 uH Shielded Power Inductor

    HCM0703-4R7-R at a glance: molded high-current power inductor, 4.7 uH ±20%, 5.5 A Irms, Isat 10 A (20% rolloff @ +25 °C), DCR 37 mOhm, 7.4 x 6.8 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM0703-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat2.8 uH
    Irms (DC, 40 °C rise)5.5 A
    Isat (20% rolloff @ +25 °C)10 A
    DCR typical @ +20 °C37 mOhm
    DCR maximum @ +20 °C40 mOhm
    K-factor (Bp-p = K x L x dI)210, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Dimensions and Pad Layout

    HCM0703-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    A molded body around an alloy or iron powder core: the winding is pressed into the magnetic material, so the field is contained inside the part and the terminals come straight out of the molding. The result is a shielded inductor with a low profile and a soft saturation curve, on a footprint that is almost all magnetic material.

    At the rated 5.5 A the winding dissipates about 1.12 W in copper alone, using the typical DCR of 37 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 235 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 210, a peak-to-peak ripple of one amp produces roughly 987 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 16 values listed for HCM0703, this is the 10th, in a family covering 0.15 uH to 33 uH.

    Compared with its neighbours in the table, HCM0703-6R8-R trades 1.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 40 mOhm becomes roughly 56.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the shielding is adequate for the adjacent trace routing.
    • Confirm the shielding is adequate for the adjacent trace routing.
    • Verify the body height against the enclosure or heat-spreader clearance.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products