Eaton HCM0703-R68-R 0.68 uH Molded Power Inductor, 15.5 A
Eaton HCM0703-R68-R 0.68 uH Molded Power Inductor, 15.5 A

Eaton HCM0703-R68-R 0.68 uH Molded Power Inductor, 15.5 A

Share
Eaton HCM0703-R68-R: molded high-current power inductor, 0.68 uH ±20%, 15.5 A Irms, Isat 25 A, DCR 5 mOhm, 7.4 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM0703-R68-R 0.68 uH Molded Power Inductor, 15.5 A

    HCM0703-R68-R at a glance: molded high-current power inductor, 0.68 uH ±20%, 15.5 A Irms, Isat 25 A (20% rolloff @ +25 °C), DCR 5 mOhm, 7.4 x 6.8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM0703-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.41 uH
    Irms (DC, 40 °C rise)15.5 A
    Isat (20% rolloff @ +25 °C)25 A
    DCR typical @ +20 °C5 mOhm
    DCR maximum @ +20 °C5.5 mOhm
    K-factor (Bp-p = K x L x dI)455, Bp-p in Gauss
    Package7.4 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4085

    Mechanical Drawing

    HCM0703-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4085: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    This is one of the molded power inductors used across VRM, point-of-load and multiphase regulator designs. The family covers a wide inductance range in standard footprints, and every row is characterised for both typical and maximum DCR so the loss budget can be built either way.

    The DCR figure of 5 mOhm is what sets the efficiency: at 15.5 A the winding drops about 0.077 mV and dissipates 1.2 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 212 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 455 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 309 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Within the HCM0703 family this is value 4 of 16, in a range that runs from 0.15 uH to 33 uH.

    Compared with its neighbours in the table, HCM0703-R82-R trades 4.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 7.4 x 6.8 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-loadmodules; desktop and server vrms and evrds; base station equipment; laptop and notebook regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 5.5 mOhm becomes roughly 7.77 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Check the hot DCR before signing off the efficiency budget.
    • Verify the body height against the enclosure or heat-spreader clearance.
    • Confirm the peak transient current stays under Isat with tolerance margin.

    Frequently Asked Questions

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products