Eaton HCM1103-2R2-R 2.2 uH High-Current Inductor 8.4 mOhm
Eaton HCM1103-2R2-R 2.2 uH High-Current Inductor 8.4 mOhm

Eaton HCM1103-2R2-R 2.2 uH High-Current Inductor 8.4 mOhm

Share
Eaton HCM1103-2R2-R: molded high-current power inductor, 2.2 uH ±20%, 13 A Irms, Isat 16 A, DCR 8.4 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1103-2R2-R 2.2 uH High-Current Inductor 8.4 mOhm

    HCM1103-2R2-R at a glance: molded high-current power inductor, 2.2 uH ±20%, 13 A Irms, Isat 16 A (20% rolloff @ +25 °C), DCR 8.4 mOhm, 11.5 x 10.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1103-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.2 uH
    Irms (DC, 40 °C rise)13 A
    Isat (20% rolloff @ +25 °C)16 A
    DCR typical @ +20 °C8.4 mOhm
    DCR maximum @ +20 °C9 mOhm
    K-factor (Bp-p = K x L x dI)264, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4449

    Outline Drawing

    HCM1103-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4449: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    A molded body around an alloy or iron powder core: the winding is pressed into the magnetic material, so the field is contained inside the part and the terminals come straight out of the molding. The result is a shielded inductor with a low profile and a soft saturation curve, on a footprint that is almost all magnetic material.

    At the rated 13 A the winding dissipates about 1.42 W in copper alone, using the typical DCR of 8.4 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 282 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 264 means the flux swing is about 581 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 12 values listed for HCM1103, this is the 6th, in a family covering 0.12 uH to 22 uH.

    Compared with its neighbours in the table, HCM1103-3R3-R trades 6 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 11.5 x 10.3 mm body at 3.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 9 mOhm becomes roughly 12.7 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Verify the body height against the enclosure or heat-spreader clearance.
    • Verify the body height against the enclosure or heat-spreader clearance.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.

    Frequently Asked Questions

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products