Eaton HCM1104-220-R 22 uH Shielded Power Inductor
Eaton HCM1104-220-R 22 uH Shielded Power Inductor

Eaton HCM1104-220-R 22 uH Shielded Power Inductor

Share
Eaton HCM1104-220-R: molded high-current power inductor, 22 uH ±20%, 5 A Irms, Isat 5.5 A, DCR 60 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1104-220-R 22 uH Shielded Power Inductor

    HCM1104-220-R at a glance: molded high-current power inductor, 22 uH ±20%, 5 A Irms, Isat 5.5 A (20% rolloff @ +25 °C), DCR 60 mOhm, 11.5 x 10.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1104-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat12.3 uH
    Irms (DC, 40 °C rise)5 A
    Isat (20% rolloff @ +25 °C)5.5 A
    DCR typical @ +20 °C60 mOhm
    DCR maximum @ +20 °C66 mOhm
    K-factor (Bp-p = K x L x dI)92, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4370

    Outline Drawing

    HCM1104-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4370: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    At the rated 5 A the winding dissipates about 1.5 W in copper alone, using the typical DCR of 60 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 333 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 92 means the flux swing is about 2,024 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    What This Family Is For

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Within the HCM1104 family this is value 12 of 12, in a range that runs from 0.2 uH to 22 uH.

    Compared with its neighbours in the table, HCM1104-100-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 66 mOhm becomes roughly 93.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Verify the body height against the enclosure or heat-spreader clearance.
    • Confirm the peak transient current stays under Isat with tolerance margin.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message