Eaton HCM1305-330-R 33.0 uH Shielded Power Inductor
Eaton HCM1305-330-R 33.0 uH Shielded Power Inductor

Eaton HCM1305-330-R 33.0 uH Shielded Power Inductor

Share
Eaton HCM1305-330-R: molded high-current power inductor, 33.0 uH ±20%, 5.2 A Irms, Isat 8 A, DCR 74.5 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1305-330-R 33.0 uH Shielded Power Inductor

    HCM1305-330-R at a glance: molded high-current power inductor, 33.0 uH ±20%, 5.2 A Irms, Isat 8 A (20% rolloff @ +25 °C), DCR 74.5 mOhm, 13.8 x 12.5 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1305-330-R
    OCL (open circuit inductance)33.0 uH ±20%
    FLL minimum, at Isat21.1 uH
    Irms (DC, 40 °C rise)5.2 A
    Isat (20% rolloff @ +25 °C)8 A
    DCR typical @ +20 °C74.5 mOhm
    DCR maximum @ +20 °C85.5 mOhm
    K-factor (Bp-p = K x L x dI)48, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4371

    Outline Drawing

    HCM1305-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4371: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    A molded body around an alloy or iron powder core: the winding is pressed into the magnetic material, so the field is contained inside the part and the terminals come straight out of the molding. The result is a shielded inductor with a low profile and a soft saturation curve, on a footprint that is almost all magnetic material.

    The DCR figure of 74.5 mOhm is what sets the efficiency: at 5.2 A the winding drops about 0.387 mV and dissipates 2.01 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 1,056 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 48, a peak-to-peak ripple of one amp produces roughly 1,584 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    The HCM1305 family spans 0.1 uH to 33 uH; this row sits at position 21 of 21.

    One step down the table, HCM1305-220-R, sits at 22.0 uH with 6.2 A and 45 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 85.5 mOhm becomes roughly 121 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Check the hot DCR before signing off the efficiency budget.
    • Build the thermal design on the maximum DCR, not the typical one.
    • Confirm the peak transient current stays under Isat with tolerance margin.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products