Eaton HCM1305-R68-R Molded Inductor 0.68 uH, Isat 54 A
Eaton HCM1305-R68-R Molded Inductor 0.68 uH, Isat 54 A

Eaton HCM1305-R68-R Molded Inductor 0.68 uH, Isat 54 A

Share
Eaton HCM1305-R68-R: molded high-current power inductor, 0.68 uH ±20%, 34 A Irms, Isat 54 A, DCR 1.15 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1305-R68-R Molded Inductor 0.68 uH, Isat 54 A

    HCM1305-R68-R at a glance: molded high-current power inductor, 0.68 uH ±20%, 34 A Irms, Isat 54 A (20% rolloff @ +25 °C), DCR 1.15 mOhm, 13.8 x 12.5 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1305-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.44 uH
    Irms (DC, 40 °C rise)34 A
    Isat (20% rolloff @ +25 °C)54 A
    DCR typical @ +20 °C1.15 mOhm
    DCR maximum @ +20 °C1.33 mOhm
    K-factor (Bp-p = K x L x dI)500, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4371

    Dimensions and Pad Layout

    HCM1305-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4371: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    With 1.15 mOhm typical, the I-squared-R loss at the full 34 A rating is about 1.33 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 991 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 500, a peak-to-peak ripple of one amp produces roughly 340 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Within the HCM1305 family this is value 6 of 21, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCM1305-R56-R, sits at 0.56 uH with 36 A and 1.15 mOhm – the lower inductance buys about 5 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; base station equipment; notebook and laptop regulators.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 1.33 mOhm becomes roughly 1.88 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.

    Frequently Asked Questions

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products