Eaton HCM1707-150-R 15 uH Shielded Power Inductor
Eaton HCM1707-150-R 15 uH Shielded Power Inductor

Eaton HCM1707-150-R 15 uH Shielded Power Inductor

Share
Eaton HCM1707-150-R: molded high-current power inductor, 15 uH ±20%, 12 A Irms, Isat 13 A, DCR 14.5 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1707-150-R 15 uH Shielded Power Inductor

    HCM1707-150-R at a glance: molded high-current power inductor, 15 uH ±20%, 12 A Irms, Isat 13 A (20% rolloff @ +25 °C), DCR 14.5 mOhm, 17.5 x 17.2 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1707-150-R
    OCL (open circuit inductance)15 uH ±20%
    FLL minimum, at Isat9.6 uH
    Irms (DC, 40 °C rise)12 A
    Isat (20% rolloff @ +25 °C)13 A
    DCR typical @ +20 °C14.5 mOhm
    DCR maximum @ +20 °C15.5 mOhm
    K-factor (Bp-p = K x L x dI)43, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10295

    Outline Drawing

    HCM1707-150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10295: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    The DCR figure of 14.5 mOhm is what sets the efficiency: at 12 A the winding drops about 0.174 mV and dissipates 2.09 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 1,268 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 43, a peak-to-peak ripple of one amp produces roughly 645 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Positioning in the Range

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 11 values listed for HCM1707, this is the 7th, in a family covering 1.5 uH to 68 uH.

    One step down the table, HCM1707-100-R, sits at 10 uH with 14 A and 9.3 mOhm – the lower inductance buys about 4.5 A of extra current in the same body.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; data networking and storage systems; base station equipment.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 15.5 mOhm becomes roughly 21.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the shielding is adequate for the adjacent trace routing.
    • Confirm the shielding is adequate for the adjacent trace routing.
    • Confirm the shielding is adequate for the adjacent trace routing.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    How much inductance is left at rated current?
    That is what the saturation column describes. Isat is the peak current at which inductance has fallen by the stated percentage, so at the rated DC current the part is still inside that boundary.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products