Eaton HCM1707-330-R 33 uH High-Current Inductor 35 mOhm
Eaton HCM1707-330-R 33 uH High-Current Inductor 35 mOhm

Eaton HCM1707-330-R 33 uH High-Current Inductor 35 mOhm

Share
Eaton HCM1707-330-R: molded high-current power inductor, 33 uH ±20%, 9 A Irms, Isat 10 A, DCR 35 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1707-330-R 33 uH High-Current Inductor 35 mOhm

    HCM1707-330-R at a glance: molded high-current power inductor, 33 uH ±20%, 9 A Irms, Isat 10 A (20% rolloff @ +25 °C), DCR 35 mOhm, 17.5 x 17.2 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1707-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat21.1 uH
    Irms (DC, 40 °C rise)9 A
    Isat (20% rolloff @ +25 °C)10 A
    DCR typical @ +20 °C35 mOhm
    DCR maximum @ +20 °C37 mOhm
    K-factor (Bp-p = K x L x dI)28, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10295

    Mechanical Drawing

    HCM1707-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10295: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    Molded construction is what gives this family its mechanical robustness and its shielding. Because the core surrounds the winding on all sides, the leakage field that would otherwise couple into adjacent traces is small, and the part can be placed close to sensitive nodes.

    With 35 mOhm typical, the I-squared-R loss at the full 9 A rating is about 2.83 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 1,650 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 28 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 924 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    In the HCM1707 line-up this part is number 9 of 11 by inductance, between 1.5 uH and 68 uH.

    Compared with its neighbours in the table, HCM1707-470-R trades 2.7 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; data networking and storage systems; base station equipment.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 37 mOhm becomes roughly 52.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Allow for copper drift: resistance rises with temperature at roughly 0.4 % per °C.
    • Check the hot DCR before signing off the efficiency budget.

    Frequently Asked Questions

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    What makes a molded inductor different?
    The winding is pressed into the magnetic powder with no bobbin or air gap in the path. That is why the body is almost all magnetic material, the DCR is low for the size, and the part is mechanically robust.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products