Eaton HCM1707-680-R 68 uH Shielded Power Inductor
Eaton HCM1707-680-R 68 uH Shielded Power Inductor

Eaton HCM1707-680-R 68 uH Shielded Power Inductor

Share
Eaton HCM1707-680-R: molded high-current power inductor, 68 uH ±20%, 5.2 A Irms, Isat 6.5 A, DCR 74 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1707-680-R 68 uH Shielded Power Inductor

    HCM1707-680-R at a glance: molded high-current power inductor, 68 uH ±20%, 5.2 A Irms, Isat 6.5 A (20% rolloff @ +25 °C), DCR 74 mOhm, 17.5 x 17.2 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1707-680-R
    OCL (open circuit inductance)68 uH ±20%
    FLL minimum, at Isat43.5 uH
    Irms (DC, 40 °C rise)5.2 A
    Isat (20% rolloff @ +25 °C)6.5 A
    DCR typical @ +20 °C74 mOhm
    DCR maximum @ +20 °C85 mOhm
    K-factor (Bp-p = K x L x dI)20, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10295

    Outline Drawing

    HCM1707-680-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10295: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    This is one of the molded power inductors used across VRM, point-of-load and multiphase regulator designs. The family covers a wide inductance range in standard footprints, and every row is characterised for both typical and maximum DCR so the loss budget can be built either way.

    At the rated 5.2 A the winding dissipates about 2 W in copper alone, using the typical DCR of 74 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Energy storage at the saturation current is around 1,436 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 20 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,360 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCM family is the commercial molded range: shielded powder-core parts from a 5.5 mm footprint up to a 17.5 mm body, covering 0.1 uH to tens of microhenry at currents from a few amps to over a hundred.

    Of the 11 values listed for HCM1707, this is the 11th, in a family covering 1.5 uH to 68 uH.

    Compared with its neighbours in the table, HCM1707-470-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules; desktop and server vrms and evrds; data networking and storage systems; base station equipment.
    • The DCR columns are typical and maximum at +20 °C. Copper rises about 0.4 % per °C, so the hot resistance is higher than either column suggests.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 85 mOhm becomes roughly 120 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: two DCR columns let the loss budget be built either on the typical part or on the worst-case part. Use maximum for a guaranteed thermal design, typical for a nominal one.

    • Confirm the shielding is adequate for the adjacent trace routing.
    • Confirm the peak transient current stays under Isat with tolerance margin.
    • Verify the body height against the enclosure or heat-spreader clearance.

    Frequently Asked Questions

    Can two parts be stacked for higher current?
    Stacking halves the inductance and doubles the current capability in theory, but the two DCRs are not matched and the magnetic coupling is uncontrolled. Use a larger part instead.

    How much does the inductance drop at rated current?
    That is what the Isat column quantifies. At the rated DC current the part is still inside the rolloff boundary, but the ripple calculation should use the FLL column rather than OCL.

    Is it magnetically shielded?
    Yes. The powder core surrounds the winding, so the leakage field is small and the part can sit close to sensitive traces without a shield can.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products