Eaton HCM1A0503-100-R AEC-Q200 Inductor 10 uH, Isat 2.3 A
Eaton HCM1A0503-100-R AEC-Q200 Inductor 10 uH, Isat 2.3 A

Eaton HCM1A0503-100-R AEC-Q200 Inductor 10 uH, Isat 2.3 A

Share
Eaton HCM1A0503-100-R: AEC-Q200 automotive power inductor, 10 uH ±20%, 2.4 A Irms, Isat 2.3 A, DCR 90 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM1A0503-100-R AEC-Q200 Inductor 10 uH, Isat 2.3 A

    HCM1A0503-100-R at a glance: AEC-Q200 automotive power inductor, 10 uH ±20%, 2.4 A Irms, Isat 2.3 A (20% rolloff @ +25 °C), DCR 90 mOhm, 5.5 x 5.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0503-100-R
    OCL (open circuit inductance)10 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)2.4 A
    Isat (20% rolloff @ +25 °C)2.3 A
    DCR typical @ +20 °C90 mOhm
    DCR maximum @ +20 °C108 mOhm
    K-factor (Bp-p = K x L x dI)191, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10547

    Mechanical Drawing

    HCM1A0503-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10547: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.518 W from a typical DCR of 90 mOhm at 2.4 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 26.4 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 191 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,910 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A0503 family spans 0.2 uH to 10 uH; this row sits at position 15 of 15.

    One step down the table, HCM1A0503-6R8-R, sits at 6.8 uH with 2.3 A and 81 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: alloy powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 108 mOhm becomes roughly 165 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message