Eaton HCM1A0503-1R0-R 1.0 uH Automotive Power Inductor
Eaton HCM1A0503-1R0-R 1.0 uH Automotive Power Inductor

Eaton HCM1A0503-1R0-R 1.0 uH Automotive Power Inductor

Share
Eaton HCM1A0503-1R0-R: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 7.1 A Irms, Isat 8.5 A, DCR 10.4 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM1A0503-1R0-R 1.0 uH Automotive Power Inductor

    HCM1A0503-1R0-R at a glance: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 7.1 A Irms, Isat 8.5 A (20% rolloff @ +25 °C), DCR 10.4 mOhm, 5.5 x 5.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0503-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.64 uH
    Irms (DC, 40 °C rise)7.1 A
    Isat (20% rolloff @ +25 °C)8.5 A
    DCR typical @ +20 °C10.4 mOhm
    DCR maximum @ +20 °C11.4 mOhm
    K-factor (Bp-p = K x L x dI)569, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10547

    Mechanical Dimensions & Pad Layout

    HCM1A0503-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10547: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 7.1 A the winding dissipates about 0.524 W in copper alone, using the typical DCR of 10.4 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 36.1 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 569, a peak-to-peak ripple of one amp produces roughly 569 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0503 line-up this part is number 8 of 15 by inductance, between 0.2 uH and 10 uH.

    One step down the table, HCM1A0503-R75-R, sits at 0.75 uH with 7.8 A and 8.5 mOhm – the lower inductance buys about 2.6 A of extra current in the same body.

    • Core material: alloy powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 11.4 mOhm becomes roughly 17.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products