Eaton HCM1A0503-4R7-R 4.7 uH Automotive Power Inductor
Eaton HCM1A0503-4R7-R 4.7 uH Automotive Power Inductor

Eaton HCM1A0503-4R7-R 4.7 uH Automotive Power Inductor

Share
Eaton HCM1A0503-4R7-R: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 3.1 A Irms, Isat 4.2 A, DCR 54 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM1A0503-4R7-R 4.7 uH Automotive Power Inductor

    HCM1A0503-4R7-R at a glance: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 3.1 A Irms, Isat 4.2 A (20% rolloff @ +25 °C), DCR 54 mOhm, 5.5 x 5.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0503-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat3 uH
    Irms (DC, 40 °C rise)3.1 A
    Isat (20% rolloff @ +25 °C)4.2 A
    DCR typical @ +20 °C54 mOhm
    DCR maximum @ +20 °C60 mOhm
    K-factor (Bp-p = K x L x dI)239, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10547

    Outline Drawing

    HCM1A0503-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10547: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 54 mOhm is what sets the efficiency: at 3.1 A the winding drops about 0.167 mV and dissipates 0.519 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 41.5 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 239 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,123 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 15 values listed for HCM1A0503, this is the 12th, in a family covering 0.2 uH to 10 uH.

    The next value up in the same family, HCM1A0503-5R6-R, gives 5.6 uH at 2.8 A and DCR 63 mOhm: the extra inductance costs about 1 A of rated current.

    • Core material: alloy powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 60 mOhm becomes roughly 91.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products