Eaton HCM1A0503V2-R75-R 0.75 uH Automotive Power Inductor
Eaton HCM1A0503V2-R75-R 0.75 uH Automotive Power Inductor

Eaton HCM1A0503V2-R75-R 0.75 uH Automotive Power Inductor

Share
Eaton HCM1A0503V2-R75-R: AEC-Q200 automotive power inductor, 0.75 uH ±20%, 10 A Irms, Isat 11.5 A, DCR 6.6 mOhm, 5.7 x 5.4 mm.
    • Product Details
    • Download

    Eaton HCM1A0503V2-R75-R 0.75 uH Automotive Power Inductor

    HCM1A0503V2-R75-R at a glance: AEC-Q200 automotive power inductor, 0.75 uH ±20%, 10 A Irms, Isat 11.5 A (20% rolloff @ +25 °C), DCR 6.6 mOhm, 5.7 x 5.4 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0503V2-R75-R
    OCL (open circuit inductance)0.75 uH ±20%
    FLL minimum, at Isat0.48 uH
    Irms (DC, 40 °C rise)10 A
    Isat (20% rolloff @ +25 °C)11.5 A
    DCR typical @ +20 °C6.6 mOhm
    DCR maximum @ +20 °C7.7 mOhm
    SRF typical57 MHz
    K-factor (Bp-p = K x L x dI)720, Bp-p in Gauss
    Package5.7 x 5.4 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10910

    Mechanical Dimensions & Pad Layout

    HCM1A0503V2-R75-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10910: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 6.6 mOhm is what sets the efficiency: at 10 A the winding drops about 0.066 mV and dissipates 0.66 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 49.6 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 720, a peak-to-peak ripple of one amp produces roughly 540 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 57 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0503V2 line-up this part is number 7 of 15 by inductance, between 0.2 uH and 10 uH.

    The next value up in the same family, HCM1A0503V2-1R0-R, gives 1.0 uH at 8.4 A and DCR 10 mOhm: the extra inductance costs about 1.6 A of rated current.

    • Core material: alloy powder core, 5.7 x 5.4 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 7.7 mOhm becomes roughly 11.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products