Eaton HCM1A0703-220-R 22 uH AEC-Q200 Inductor, 2 A
Eaton HCM1A0703-220-R 22 uH AEC-Q200 Inductor, 2 A

Eaton HCM1A0703-220-R 22 uH AEC-Q200 Inductor, 2 A

Share
Eaton HCM1A0703-220-R: AEC-Q200 automotive power inductor, 22 uH ±20%, 2 A Irms, Isat 3.4 A, DCR 135 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCM1A0703-220-R 22 uH AEC-Q200 Inductor, 2 A

    HCM1A0703-220-R at a glance: AEC-Q200 automotive power inductor, 22 uH ±20%, 2 A Irms, Isat 3.4 A (20% rolloff @ +25 °C), DCR 135 mOhm, 7.4 x 7 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0703-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14.1 uH
    Irms (DC, 40 °C rise)2 A
    Isat (20% rolloff @ +25 °C)3.4 A
    DCR typical @ +20 °C135 mOhm
    DCR maximum @ +20 °C149 mOhm
    K-factor (Bp-p = K x L x dI)121, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10548

    Outline Drawing

    HCM1A0703-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10548: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    The DCR figure of 135 mOhm is what sets the efficiency: at 2 A the winding drops about 0.27 mV and dissipates 0.54 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 127 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 121 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,662 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 19 values listed for HCM1A0703, this is the 18th, in a family covering 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A0703-330-R, gives 33 uH at 1.6 A and DCR 220 mOhm: the extra inductance costs about 0.6 A of rated current.

    • Core material: alloy powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 149 mOhm becomes roughly 228 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products