Eaton HCM1A0703-4R7-R 4.7 uH Automotive Power Inductor
Eaton HCM1A0703-4R7-R 4.7 uH Automotive Power Inductor

Eaton HCM1A0703-4R7-R 4.7 uH Automotive Power Inductor

Share
Eaton HCM1A0703-4R7-R: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 4.1 A Irms, Isat 8.8 A, DCR 37 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCM1A0703-4R7-R 4.7 uH Automotive Power Inductor

    HCM1A0703-4R7-R at a glance: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 4.1 A Irms, Isat 8.8 A (20% rolloff @ +25 °C), DCR 37 mOhm, 7.4 x 7 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0703-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat3 uH
    Irms (DC, 40 °C rise)4.1 A
    Isat (20% rolloff @ +25 °C)8.8 A
    DCR typical @ +20 °C37 mOhm
    DCR maximum @ +20 °C40 mOhm
    K-factor (Bp-p = K x L x dI)235, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10548

    Mechanical Dimensions & Pad Layout

    HCM1A0703-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10548: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    With 37 mOhm typical, the I-squared-R loss at the full 4.1 A rating is about 0.622 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 182 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 235 means the flux swing is about 1,104 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A0703 family spans 0.1 uH to 33 uH; this row sits at position 13 of 19.

    The next value up in the same family, HCM1A0703-6R8-R, gives 6.8 uH at 3.5 A and DCR 54 mOhm: the extra inductance costs about 1.4 A of rated current.

    • Core material: alloy powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 40 mOhm becomes roughly 61.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products