Eaton HCM1A0703-R68-R 0.68 uH Shielded Automotive Inductor
Eaton HCM1A0703-R68-R 0.68 uH Shielded Automotive Inductor

Eaton HCM1A0703-R68-R 0.68 uH Shielded Automotive Inductor

Share
Eaton HCM1A0703-R68-R: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 10 A Irms, Isat 15 A, DCR 5 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCM1A0703-R68-R 0.68 uH Shielded Automotive Inductor

    HCM1A0703-R68-R at a glance: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 10 A Irms, Isat 15 A (20% rolloff @ +25 °C), DCR 5 mOhm, 7.4 x 7 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0703-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.43 uH
    Irms (DC, 40 °C rise)10 A
    Isat (20% rolloff @ +25 °C)15 A
    DCR typical @ +20 °C5 mOhm
    DCR maximum @ +20 °C5.5 mOhm
    K-factor (Bp-p = K x L x dI)574, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10548

    Mechanical Dimensions & Pad Layout

    HCM1A0703-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10548: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    Copper loss at the rated current works out to roughly 0.5 W from a typical DCR of 5 mOhm at 10 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 76.5 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 574 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 390 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 19 values listed for HCM1A0703, this is the 7th, in a family covering 0.1 uH to 33 uH.

    One step down the table, HCM1A0703-R56-R, sits at 0.56 uH with 10.3 A and 4.7 mOhm – the lower inductance buys about 1.8 A of extra current in the same body.

    • Core material: alloy powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 5.5 mOhm becomes roughly 8.42 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products