Eaton HCM1A0703V2-220-R 22 uH Shielded Automotive Inductor
Eaton HCM1A0703V2-220-R 22 uH Shielded Automotive Inductor

Eaton HCM1A0703V2-220-R 22 uH Shielded Automotive Inductor

Share
Eaton HCM1A0703V2-220-R: AEC-Q200 automotive power inductor, 22 uH ±20%, 2 A Irms, Isat 2.9 A, DCR 135 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V2-220-R 22 uH Shielded Automotive Inductor

    HCM1A0703V2-220-R at a glance: AEC-Q200 automotive power inductor, 22 uH ±20%, 2 A Irms, Isat 2.9 A (20% rolloff @ +25 °C), DCR 135 mOhm, 7.3 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A0703V2-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14.1 uH
    Irms (DC, 40 °C rise)2 A
    Isat (20% rolloff @ +25 °C)2.9 A
    DCR typical @ +20 °C135 mOhm
    DCR maximum @ +20 °C149 mOhm
    SRF typical7 MHz
    K-factor (Bp-p = K x L x dI)134, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10911

    Outline Drawing

    HCM1A0703V2-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10911: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 135 mOhm is what sets the efficiency: at 2 A the winding drops about 0.27 mV and dissipates 0.54 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 92.5 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 134 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,948 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 7 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A0703V2 family spans 0.1 uH to 33 uH; this row sits at position 19 of 20.

    The next value up in the same family, HCM1A0703V2-330-R, gives 33 uH at 1.6 A and DCR 200 mOhm: the extra inductance costs about 1 A of rated current.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 149 mOhm becomes roughly 228 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products