Eaton HCM1A0703V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 4.8 A
Eaton HCM1A0703V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 4.8 A

Eaton HCM1A0703V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 4.8 A

Share
Eaton HCM1A0703V2-8R2-R: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 3.5 A Irms, Isat 4.8 A, DCR 53 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V2-8R2-R AEC-Q200 Inductor 8.2 uH, Isat 4.8 A

    HCM1A0703V2-8R2-R at a glance: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 3.5 A Irms, Isat 4.8 A (20% rolloff @ +25 °C), DCR 53 mOhm, 7.3 x 6.8 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0703V2-8R2-R
    OCL (open circuit inductance)8.2 uH ±20%
    FLL minimum, at Isat5.2 uH
    Irms (DC, 40 °C rise)3.5 A
    Isat (20% rolloff @ +25 °C)4.8 A
    DCR typical @ +20 °C53 mOhm
    DCR maximum @ +20 °C64 mOhm
    SRF typical14 MHz
    K-factor (Bp-p = K x L x dI)173, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10911

    Outline Drawing

    HCM1A0703V2-8R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10911: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.649 W from a typical DCR of 53 mOhm at 3.5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 94.5 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 173 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,419 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 14 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A0703V2 family spans 0.1 uH to 33 uH; this row sits at position 16 of 20.

    The next value up in the same family, HCM1A0703V2-100-R, gives 10 uH at 3.3 A and DCR 65 mOhm: the extra inductance costs about 0.3 A of rated current.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 64 mOhm becomes roughly 98 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products