Eaton HCM1A0703V2-R10-R 0.10 uH Automotive Power Inductor
Eaton HCM1A0703V2-R10-R 0.10 uH Automotive Power Inductor

Eaton HCM1A0703V2-R10-R 0.10 uH Automotive Power Inductor

Share
Eaton HCM1A0703V2-R10-R: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 29 A Irms, Isat 54 A, DCR 0.63 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V2-R10-R 0.10 uH Automotive Power Inductor

    HCM1A0703V2-R10-R at a glance: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 29 A Irms, Isat 54 A (20% rolloff @ +25 °C), DCR 0.63 mOhm, 7.3 x 6.8 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0703V2-R10-R
    OCL (open circuit inductance)0.10 uH ±20%
    FLL minimum, at Isat0.064 uH
    Irms (DC, 40 °C rise)29 A
    Isat (20% rolloff @ +25 °C)54 A
    DCR typical @ +20 °C0.63 mOhm
    DCR maximum @ +20 °C0.8 mOhm
    SRF typical350 MHz
    K-factor (Bp-p = K x L x dI)1,284, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10911

    Mechanical Drawing

    HCM1A0703V2-R10-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10911: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    The DCR figure of 0.63 mOhm is what sets the efficiency: at 29 A the winding drops about 0.018 mV and dissipates 0.53 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 146 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 1,284 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 128 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 350 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A0703V2, this is the 1th, in a family covering 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A0703V2-R15-R, gives 0.15 uH at 24 A and DCR 1.03 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.8 mOhm becomes roughly 1.22 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message