Eaton HCM1A0703V2-R22-R 0.22 uH Shielded Automotive Inductor
Eaton HCM1A0703V2-R22-R 0.22 uH Shielded Automotive Inductor

Eaton HCM1A0703V2-R22-R 0.22 uH Shielded Automotive Inductor

Share
Eaton HCM1A0703V2-R22-R: AEC-Q200 automotive power inductor, 0.22 uH ±20%, 18 A Irms, Isat 32 A, DCR 1.8 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V2-R22-R 0.22 uH Shielded Automotive Inductor

    HCM1A0703V2-R22-R at a glance: AEC-Q200 automotive power inductor, 0.22 uH ±20%, 18 A Irms, Isat 32 A (20% rolloff @ +25 °C), DCR 1.8 mOhm, 7.3 x 6.8 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0703V2-R22-R
    OCL (open circuit inductance)0.22 uH ±20%
    FLL minimum, at Isat0.13 uH
    Irms (DC, 40 °C rise)18 A
    Isat (20% rolloff @ +25 °C)32 A
    DCR typical @ +20 °C1.8 mOhm
    DCR maximum @ +20 °C2.3 mOhm
    SRF typical150 MHz
    K-factor (Bp-p = K x L x dI)1,039, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10911

    Dimensions and Pad Layout

    HCM1A0703V2-R22-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10911: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    The DCR figure of 1.8 mOhm is what sets the efficiency: at 18 A the winding drops about 0.032 mV and dissipates 0.583 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 113 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    K-factor 1,039 means the flux swing is about 229 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 150 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0703V2 family this is value 3 of 20, in a range that runs from 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A0703V2-R33-R, gives 0.33 uH at 15 A and DCR 2.9 mOhm: the extra inductance costs about 9 A of rated current.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.3 mOhm becomes roughly 3.52 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products