Eaton HCM1A0703V3-1R5-R 1.5 uH Shielded Automotive Inductor
Eaton HCM1A0703V3-1R5-R 1.5 uH Shielded Automotive Inductor

Eaton HCM1A0703V3-1R5-R 1.5 uH Shielded Automotive Inductor

Share
Eaton HCM1A0703V3-1R5-R: AEC-Q200 automotive power inductor, 1.5 uH ±20%, 8.5 A Irms, Isat 10 A, DCR 9.5 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-1R5-R 1.5 uH Shielded Automotive Inductor

    HCM1A0703V3-1R5-R at a glance: AEC-Q200 automotive power inductor, 1.5 uH ±20%, 8.5 A Irms, Isat 10 A (20% rolloff @ +25 °C), DCR 9.5 mOhm, 7.3 x 6.8 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0703V3-1R5-R
    OCL (open circuit inductance)1.5 uH ±20%
    FLL minimum, at Isat0.96 uH
    Irms (DC, 40 °C rise)8.5 A
    Isat (20% rolloff @ +25 °C)10 A
    DCR typical @ +20 °C9.5 mOhm
    DCR maximum @ +20 °C11.5 mOhm
    SRF typical35 MHz
    K-factor (Bp-p = K x L x dI)411, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Outline Drawing

    HCM1A0703V3-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 8.5 A the winding dissipates about 0.686 W in copper alone, using the typical DCR of 9.5 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 75 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 411, a peak-to-peak ripple of one amp produces roughly 616 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 35 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A0703V3, this is the 11th, in a family covering 0.1 uH to 33 uH.

    One step down the table, HCM1A0703V3-1R2-R, sits at 1.2 uH with 9 A and 8.6 mOhm – the lower inductance buys about 2 A of extra current in the same body.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 11.5 mOhm becomes roughly 17.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products