Eaton HCM1A0703V3-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A
Eaton HCM1A0703V3-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A

Eaton HCM1A0703V3-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A

Share
Eaton HCM1A0703V3-330-R: AEC-Q200 automotive power inductor, 33 uH ±20%, 1.6 A Irms, Isat 2.3 A, DCR 200 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A

    HCM1A0703V3-330-R at a glance: AEC-Q200 automotive power inductor, 33 uH ±20%, 1.6 A Irms, Isat 2.3 A (20% rolloff @ +25 °C), DCR 200 mOhm, 7.3 x 6.8 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0703V3-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat19.8 uH
    Irms (DC, 40 °C rise)1.6 A
    Isat (20% rolloff @ +25 °C)2.3 A
    DCR typical @ +20 °C200 mOhm
    DCR maximum @ +20 °C242 mOhm
    SRF typical6.5 MHz
    K-factor (Bp-p = K x L x dI)88, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Outline Drawing

    HCM1A0703V3-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.512 W from a typical DCR of 200 mOhm at 1.6 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 87.3 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 88 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,904 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 6.5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0703V3 family this is value 20 of 20, in a range that runs from 0.1 uH to 33 uH.

    Compared with its neighbours in the table, HCM1A0703V3-220-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 242 mOhm becomes roughly 370 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Verify the part marking for revision traceability in production.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products