Eaton HCM1A0703V3-3R3-R 3.3 uH Automotive Power Inductor
Eaton HCM1A0703V3-3R3-R 3.3 uH Automotive Power Inductor

Eaton HCM1A0703V3-3R3-R 3.3 uH Automotive Power Inductor

Share
Eaton HCM1A0703V3-3R3-R: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 5 A Irms, Isat 7.5 A, DCR 24.5 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-3R3-R 3.3 uH Automotive Power Inductor

    HCM1A0703V3-3R3-R at a glance: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 5 A Irms, Isat 7.5 A (20% rolloff @ +25 °C), DCR 24.5 mOhm, 7.3 x 6.8 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0703V3-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.1 uH
    Irms (DC, 40 °C rise)5 A
    Isat (20% rolloff @ +25 °C)7.5 A
    DCR typical @ +20 °C24.5 mOhm
    DCR maximum @ +20 °C28.5 mOhm
    SRF typical25 MHz
    K-factor (Bp-p = K x L x dI)305, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Outline Drawing

    HCM1A0703V3-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    With 24.5 mOhm typical, the I-squared-R loss at the full 5 A rating is about 0.613 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 92.8 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 305, a peak-to-peak ripple of one amp produces roughly 1,006 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 25 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0703V3 family this is value 13 of 20, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCM1A0703V3-2R2-R, sits at 2.2 uH with 7 A and 12.5 mOhm – the lower inductance buys about 3 A of extra current in the same body.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 28.5 mOhm becomes roughly 43.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products