Eaton HCM1A0703V3-R10-R 0.10 uH Automotive Power Inductor
Eaton HCM1A0703V3-R10-R 0.10 uH Automotive Power Inductor

Eaton HCM1A0703V3-R10-R 0.10 uH Automotive Power Inductor

Share
Eaton HCM1A0703V3-R10-R: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 29 A Irms, Isat 54 A, DCR 0.63 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-R10-R 0.10 uH Automotive Power Inductor

    HCM1A0703V3-R10-R at a glance: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 29 A Irms, Isat 54 A (20% rolloff @ +25 °C), DCR 0.63 mOhm, 7.3 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A0703V3-R10-R
    OCL (open circuit inductance)0.10 uH ±20%
    FLL minimum, at Isat0.064 uH
    Irms (DC, 40 °C rise)29 A
    Isat (20% rolloff @ +25 °C)54 A
    DCR typical @ +20 °C0.63 mOhm
    DCR maximum @ +20 °C0.8 mOhm
    SRF typical350 MHz
    K-factor (Bp-p = K x L x dI)1,429, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Mechanical Dimensions & Pad Layout

    HCM1A0703V3-R10-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 29 A the winding dissipates about 0.53 W in copper alone, using the typical DCR of 0.63 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 146 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 1,429 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 143 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 350 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A0703V3, this is the 1th, in a family covering 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A0703V3-R15-R, gives 0.15 uH at 24 A and DCR 1.03 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.8 mOhm becomes roughly 1.22 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products