Eaton HCM1A0805-150-R 15 uH AEC-Q200 Inductor, 2.5 A
Eaton HCM1A0805-150-R 15 uH AEC-Q200 Inductor, 2.5 A

Eaton HCM1A0805-150-R 15 uH AEC-Q200 Inductor, 2.5 A

Share
Eaton HCM1A0805-150-R: AEC-Q200 automotive power inductor, 15 uH ±20%, 2.5 A Irms, Isat 6 A, DCR 64 mOhm, 8.3 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805-150-R 15 uH AEC-Q200 Inductor, 2.5 A

    HCM1A0805-150-R at a glance: AEC-Q200 automotive power inductor, 15 uH ±20%, 2.5 A Irms, Isat 6 A (20% rolloff @ +25 °C), DCR 64 mOhm, 8.3 x 8 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0805-150-R
    OCL (open circuit inductance)15 uH ±20%
    FLL minimum, at Isat9.6 uH
    Irms (DC, 40 °C rise)2.5 A
    Isat (20% rolloff @ +25 °C)6 A
    DCR typical @ +20 °C64 mOhm
    DCR maximum @ +20 °C71 mOhm
    K-factor (Bp-p = K x L x dI)48, Bp-p in Gauss
    Package8.3 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10549

    Dimensions and Pad Layout

    HCM1A0805-150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10549: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.4 W from a typical DCR of 64 mOhm at 2.5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    At Isat the part holds about 270 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 48 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 720 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0805 line-up this part is number 4 of 6 by inductance, between 3.3 uH and 47 uH.

    Compared with its neighbours in the table, HCM1A0805-220-R trades 0.8 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 8.3 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 71 mOhm becomes roughly 109 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products