Eaton HCM1A0805-220-R 22 uH Shielded Automotive Inductor
Eaton HCM1A0805-220-R 22 uH Shielded Automotive Inductor

Eaton HCM1A0805-220-R 22 uH Shielded Automotive Inductor

Share
Eaton HCM1A0805-220-R: AEC-Q200 automotive power inductor, 22 uH ±20%, 2 A Irms, Isat 3.8 A, DCR 100 mOhm, 8.3 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805-220-R 22 uH Shielded Automotive Inductor

    HCM1A0805-220-R at a glance: AEC-Q200 automotive power inductor, 22 uH ±20%, 2 A Irms, Isat 3.8 A (20% rolloff @ +25 °C), DCR 100 mOhm, 8.3 x 8 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0805-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14 uH
    Irms (DC, 40 °C rise)2 A
    Isat (20% rolloff @ +25 °C)3.8 A
    DCR typical @ +20 °C100 mOhm
    DCR maximum @ +20 °C110 mOhm
    K-factor (Bp-p = K x L x dI)39, Bp-p in Gauss
    Package8.3 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10549

    Mechanical Drawing

    HCM1A0805-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10549: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    At the rated 2 A the winding dissipates about 0.4 W in copper alone, using the typical DCR of 100 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 159 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 39 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 858 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 6 values listed for HCM1A0805, this is the 5th, in a family covering 3.3 uH to 47 uH.

    The next value up in the same family, HCM1A0805-470-R, gives 47 uH at 1.8 A and DCR 145 mOhm: the extra inductance costs about 0.7 A of rated current.

    • Core material: alloy powder core, 8.3 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 110 mOhm becomes roughly 168 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products