Eaton HCM1A0805-3R3-R 3.3 uH Shielded Automotive Inductor
Eaton HCM1A0805-3R3-R 3.3 uH Shielded Automotive Inductor

Eaton HCM1A0805-3R3-R 3.3 uH Shielded Automotive Inductor

Share
Eaton HCM1A0805-3R3-R: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 8 A Irms, Isat 8 A, DCR 9 mOhm, 8.3 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805-3R3-R 3.3 uH Shielded Automotive Inductor

    HCM1A0805-3R3-R at a glance: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 8 A Irms, Isat 8 A (20% rolloff @ +25 °C), DCR 9 mOhm, 8.3 x 8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0805-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.1 uH
    Irms (DC, 40 °C rise)8 A
    Isat (20% rolloff @ +25 °C)8 A
    DCR typical @ +20 °C9 mOhm
    DCR maximum @ +20 °C10 mOhm
    K-factor (Bp-p = K x L x dI)180, Bp-p in Gauss
    Package8.3 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10549

    Outline Drawing

    HCM1A0805-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10549: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    With 9 mOhm typical, the I-squared-R loss at the full 8 A rating is about 0.576 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 106 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 180 means the flux swing is about 594 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 6 values listed for HCM1A0805, this is the 1th, in a family covering 3.3 uH to 47 uH.

    Compared with its neighbours in the table, HCM1A0805-4R7-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 8.3 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 10 mOhm becomes roughly 15.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message