Eaton HCM1A0805-470-R AEC-Q200 Inductor 47 uH, Isat 3.2 A
Eaton HCM1A0805-470-R AEC-Q200 Inductor 47 uH, Isat 3.2 A

Eaton HCM1A0805-470-R AEC-Q200 Inductor 47 uH, Isat 3.2 A

Share
Eaton HCM1A0805-470-R: AEC-Q200 automotive power inductor, 47 uH ±20%, 1.8 A Irms, Isat 3.2 A, DCR 145 mOhm, 8.3 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805-470-R AEC-Q200 Inductor 47 uH, Isat 3.2 A

    HCM1A0805-470-R at a glance: AEC-Q200 automotive power inductor, 47 uH ±20%, 1.8 A Irms, Isat 3.2 A (20% rolloff @ +25 °C), DCR 145 mOhm, 8.3 x 8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A0805-470-R
    OCL (open circuit inductance)47 uH ±20%
    FLL minimum, at Isat30 uH
    Irms (DC, 40 °C rise)1.8 A
    Isat (20% rolloff @ +25 °C)3.2 A
    DCR typical @ +20 °C145 mOhm
    DCR maximum @ +20 °C160 mOhm
    K-factor (Bp-p = K x L x dI)31, Bp-p in Gauss
    Package8.3 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10549

    Outline Drawing

    HCM1A0805-470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10549: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.47 W from a typical DCR of 145 mOhm at 1.8 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 241 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 31 means the flux swing is about 1,457 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0805 family this is value 6 of 6, in a range that runs from 3.3 uH to 47 uH.

    One step down the table, HCM1A0805-220-R, sits at 22 uH with 2 A and 100 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: alloy powder core, 8.3 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 160 mOhm becomes roughly 245 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the qualification file covers the module-level test plan.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products