Eaton HCM1A0805V2-470-R 47 uH AEC-Q200 Inductor, 2.5 A
Eaton HCM1A0805V2-470-R 47 uH AEC-Q200 Inductor, 2.5 A

Eaton HCM1A0805V2-470-R 47 uH AEC-Q200 Inductor, 2.5 A

Share
Eaton HCM1A0805V2-470-R: AEC-Q200 automotive power inductor, 47 uH ±20%, 2.5 A Irms, Isat 2.6 A, DCR 125 mOhm, 8.4 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805V2-470-R 47 uH AEC-Q200 Inductor, 2.5 A

    HCM1A0805V2-470-R at a glance: AEC-Q200 automotive power inductor, 47 uH ±20%, 2.5 A Irms, Isat 2.6 A (20% rolloff @ +25 °C), DCR 125 mOhm, 8.4 x 8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0805V2-470-R
    OCL (open circuit inductance)47 uH ±20%
    FLL minimum, at Isat30 uH
    Irms (DC, 40 °C rise)2.5 A
    Isat (20% rolloff @ +25 °C)2.6 A
    DCR typical @ +20 °C125 mOhm
    DCR maximum @ +20 °C137 mOhm
    SRF typical4.5 MHz
    K-factor (Bp-p = K x L x dI)37, Bp-p in Gauss
    Package8.4 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10902

    Mechanical Drawing

    HCM1A0805V2-470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10902: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 125 mOhm is what sets the efficiency: at 2.5 A the winding drops about 0.312 mV and dissipates 0.781 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 159 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 37 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,739 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 4.5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0805V2 family this is value 12 of 12, in a range that runs from 0.22 uH to 47 uH.

    The next value up in the same family, HCM1A0805V2-330-R, gives 33 uH at 2.7 A and DCR 103 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: alloy powder core, 8.4 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 137 mOhm becomes roughly 210 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Verify the part marking for revision traceability in production.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products