
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A0805V3-150-R |
| OCL (open circuit inductance) | 15 uH ±20% |
| FLL minimum, at Isat | 9.6 uH |
| Irms1 (DC, 40 °C rise) | 4.3 A |
| Irms2 (DC, 40 °C rise) | 3.8 A |
| Isat (20% rolloff @ +25 °C) | 4.6 A |
| DCR maximum @ +20 °C | 52 mOhm |
| SRF typical | 9.5 MHz |
| K-factor (Bp-p = K x L x dI) | 65, Bp-p in Gauss |
| Package | 8 x 7.5 mm |
| Height | 5.4 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1485 |

Drawing reproduced from Eaton Technical Data ELX1485: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.
At the rated 4.3 A the winding dissipates about 0.961 W in copper alone, using the typical DCR of 52 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.
Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.
Energy storage at the saturation current is around 159 uJ, the number that connects the inductance and the current rating into a single transient figure.
The K-factor of 65 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 975 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Two Irms columns are quoted because two self-heating levels are allowed: 4.3 A and 3.8 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.
Self-resonant frequency is 9.5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Of the 14 values listed for HCM1A0805V3, this is the 9th, in a family covering 0.22 uH to 100 uH.
The next value up in the same family, HCM1A0805V3-220-R, gives 22 uH at 3.5 A and DCR 70 mOhm: the extra inductance costs about 0.8 A of rated current.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 52 mOhm becomes roughly 79.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What is the operating temperature range?
The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.
Does the automotive grade change the electrical values?
Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd