Eaton HCM1A0805V3-2R2-R 2.2 uH Automotive Power Inductor
Eaton HCM1A0805V3-2R2-R 2.2 uH Automotive Power Inductor

Eaton HCM1A0805V3-2R2-R 2.2 uH Automotive Power Inductor

Share
Eaton HCM1A0805V3-2R2-R: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 11 A Irms, Isat 9.6 A, DCR 8.5 mOhm, 8 x 7.5 mm.
    • Product Details
    • Download

    Eaton HCM1A0805V3-2R2-R 2.2 uH Automotive Power Inductor

    HCM1A0805V3-2R2-R at a glance: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 11 A Irms, Isat 9.6 A (20% rolloff @ +25 °C), DCR 8.5 mOhm, 8 x 7.5 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A0805V3-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.41 uH
    Irms1 (DC, 40 °C rise)11 A
    Irms2 (DC, 40 °C rise)9.5 A
    Isat (20% rolloff @ +25 °C)9.6 A
    DCR maximum @ +20 °C8.5 mOhm
    SRF typical28 MHz
    K-factor (Bp-p = K x L x dI)170, Bp-p in Gauss
    Package8 x 7.5 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1485

    Dimensions and Pad Layout

    HCM1A0805V3-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1485: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 11 A the winding dissipates about 1.03 W in copper alone, using the typical DCR of 8.5 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 101 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 170 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 374 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Two Irms columns are quoted because two self-heating levels are allowed: 11 A and 9.5 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.

    Self-resonant frequency is 28 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0805V3 line-up this part is number 5 of 14 by inductance, between 0.22 uH and 100 uH.

    The next value up in the same family, HCM1A0805V3-3R3-R, gives 3.3 uH at 10 A and DCR 10 mOhm: the extra inductance costs about 6 A of rated current.

    • Core material: alloy powder core, 8 x 7.5 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 8.5 mOhm becomes roughly 13 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products