
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A0805V3-330-R |
| OCL (open circuit inductance) | 33 uH ±20% |
| FLL minimum, at Isat | 21 uH |
| Irms1 (DC, 40 °C rise) | 2.8 A |
| Irms2 (DC, 40 °C rise) | 2.5 A |
| Isat (20% rolloff @ +25 °C) | 4 A |
| DCR maximum @ +20 °C | 125 mOhm |
| SRF typical | 6.1 MHz |
| K-factor (Bp-p = K x L x dI) | 41, Bp-p in Gauss |
| Package | 8 x 7.5 mm |
| Height | 5.4 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1485 |

Drawing reproduced from Eaton Technical Data ELX1485: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.
With 125 mOhm typical, the I-squared-R loss at the full 2.8 A rating is about 0.98 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.
Energy storage at the saturation current is around 264 uJ, the number that connects the inductance and the current rating into a single transient figure.
With K = 41, a peak-to-peak ripple of one amp produces roughly 1,353 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.
Two Irms columns are quoted because two self-heating levels are allowed: 2.8 A and 2.5 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.
Self-resonant frequency is 6.1 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
In the HCM1A0805V3 line-up this part is number 11 of 14 by inductance, between 0.22 uH and 100 uH.
The next value up in the same family, HCM1A0805V3-470-R, gives 47 uH at 2.5 A and DCR 147 mOhm: the extra inductance costs about 1 A of rated current.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 125 mOhm becomes roughly 191 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd