
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A0805V3-470-R |
| OCL (open circuit inductance) | 47 uH ±20% |
| FLL minimum, at Isat | 26 uH |
| Irms1 (DC, 40 °C rise) | 2.5 A |
| Irms2 (DC, 40 °C rise) | 2.2 A |
| Isat (20% rolloff @ +25 °C) | 4.7 A |
| DCR maximum @ +20 °C | 147 mOhm |
| SRF typical | 4 MHz |
| K-factor (Bp-p = K x L x dI) | 52, Bp-p in Gauss |
| Package | 8 x 7.5 mm |
| Height | 5.4 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1485 |

Drawing reproduced from Eaton Technical Data ELX1485: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.
With 147 mOhm typical, the I-squared-R loss at the full 2.5 A rating is about 0.919 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.
Energy storage at the saturation current is around 519 uJ, the number that connects the inductance and the current rating into a single transient figure.
K-factor 52 means the flux swing is about 2,444 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.
Two Irms columns are quoted because two self-heating levels are allowed: 2.5 A and 2.2 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.
Self-resonant frequency is 4 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Within the HCM1A0805V3 family this is value 12 of 14, in a range that runs from 0.22 uH to 100 uH.
Compared with its neighbours in the table, HCM1A0805V3-680-R trades 0.7 A of rated current for the next inductance step, which is the usual compromise in this family.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 147 mOhm becomes roughly 225 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What is the operating temperature range?
The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
What is the self-resonant frequency used for?
It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd