Eaton HCM1A1104-3R3-R 3.3 uH Shielded Automotive Inductor
Eaton HCM1A1104-3R3-R 3.3 uH Shielded Automotive Inductor

Eaton HCM1A1104-3R3-R 3.3 uH Shielded Automotive Inductor

Share
Eaton HCM1A1104-3R3-R: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 8.2 A Irms, Isat 11.5 A, DCR 10.8 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104-3R3-R 3.3 uH Shielded Automotive Inductor

    HCM1A1104-3R3-R at a glance: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 8.2 A Irms, Isat 11.5 A (20% rolloff @ +25 °C), DCR 10.8 mOhm, 11.5 x 10.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1104-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.11 uH
    Irms (DC, 40 °C rise)8.2 A
    Isat (20% rolloff @ +25 °C)11.5 A
    DCR typical @ +20 °C10.8 mOhm
    DCR maximum @ +20 °C11.8 mOhm
    K-factor (Bp-p = K x L x dI)163, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10550

    Mechanical Dimensions & Pad Layout

    HCM1A1104-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10550: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    The DCR figure of 10.8 mOhm is what sets the efficiency: at 8.2 A the winding drops about 0.089 mV and dissipates 0.726 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 218 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 163 means the flux swing is about 538 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1104 family spans 0.2 uH to 100 uH; this row sits at position 10 of 19.

    The next value up in the same family, HCM1A1104-4R7-R, gives 4.7 uH at 6.5 A and DCR 15 mOhm: the extra inductance costs about 4 A of rated current.

    • Core material: alloy powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 11.8 mOhm becomes roughly 18.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products