Eaton HCM1A1104-470-R 47 uH Shielded Automotive Inductor
Eaton HCM1A1104-470-R 47 uH Shielded Automotive Inductor

Eaton HCM1A1104-470-R 47 uH Shielded Automotive Inductor

Share
Eaton HCM1A1104-470-R: AEC-Q200 automotive power inductor, 47 uH ±20%, 1.9 A Irms, Isat 3.6 A, DCR 165 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104-470-R 47 uH Shielded Automotive Inductor

    HCM1A1104-470-R at a glance: AEC-Q200 automotive power inductor, 47 uH ±20%, 1.9 A Irms, Isat 3.6 A (20% rolloff @ +25 °C), DCR 165 mOhm, 11.5 x 10.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1104-470-R
    OCL (open circuit inductance)47 uH ±20%
    FLL minimum, at Isat30.1 uH
    Irms (DC, 40 °C rise)1.9 A
    Isat (20% rolloff @ +25 °C)3.6 A
    DCR typical @ +20 °C165 mOhm
    DCR maximum @ +20 °C181 mOhm
    K-factor (Bp-p = K x L x dI)36, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10550

    Outline Drawing

    HCM1A1104-470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10550: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    Copper loss at the rated current works out to roughly 0.596 W from a typical DCR of 165 mOhm at 1.9 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 305 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 36, a peak-to-peak ripple of one amp produces roughly 1,692 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1104 family spans 0.2 uH to 100 uH; this row sits at position 18 of 19.

    One step down the table, HCM1A1104-330-R, sits at 33 uH with 2.8 A and 92 mOhm – the lower inductance buys about 1.3 A of extra current in the same body.

    • Core material: alloy powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 181 mOhm becomes roughly 277 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products